Gadgetory

installing trim around windows and doors is as easy as measure mark in install with a miles craft trim 45 to use the trim 45 start by holding the button upwards to adjust the reveal gauge to your desired reveal around the door or window the reveal gauge has a maximum reveal of 1/2 inch and can be adjusted for a shallower reveal in 1/8 inch increments once you've determined to reveal push the button back down to lock in the desired setting to install the trim for your project start by aligning the reveal gauge to the jam corner and make your horizontal and vertical marks using the edges of the reveal gauge scale the front and back of the trim 45 are used to make all marks or measurements for your jams and trim casings then repeat this for all four corners then to measure for your projects trim nail the trim 45 in place using the two small holes just above the reveal gauge to insert nails then using the tape measure slots in the body the trim 45 measure the distance between your marks to determine the fascia trim length to help hold the tape measure in place there's two magnets next to each of the tape measure slots after you've measured the links to your trim pieces set your miter saw for a 45-degree cut and cut one end of the trim casing then using that 45-degree end you just cut use the built-in trim plate to clamp your 45 degree miter cut piece onto the trim plate with the backside of your trim piece facing up then clamp the trim 45 to the backside of the trim using the trim plate to keep the trim 45 in position then using the indicated tape measure slot measure the finished trim length and market next reset you reveal gauge to zero flip the trim 45 over and make a 45-degree angle mark on the trim at the finish length using the 45 degree angle head your mark should start at the corner of the reveal gauge and follow the 45 degree angle after marking the finished length cut the trim along the angle mark repeat the cutting action for the remaining trim pieces and then install with the miles craft trim 45 installing trim around windows and doors is as easy as measure mark and install miles craft always the better idea introducing the miles craft hook driver installing hooks has never been so easy this two-in-one tool provides a comfortable t-handle grip that accepts quarter-inch hex bits this can be used to tighten various types of fasteners it offers a uniquely profiled bit that can be used with any drill or quarter-inch impact and accepts a variety of hooks and rings up to quarter inch in size no more sore fingers and hands or twisting screwdrivers to install your hooks simply pre-drill the pilot hole for your hook and start the threads by hand use a drill quarter-inch impact or the miles craft grip handle along with the hook driver bit to complete the installation to your required depth if you are looking to build that backyard swing or make a plant hanger for your front porch be sure to check out the miles craft hook driver it's the perfect tool for any homeowner or craftsman miles craft always the better idea so we've all been there we have a really tight confined space that we need to drill either a screw into or a hole through and our impact driver and drill they just don't work they're too big and too bulky to fit into the space luckily Laos craft is coming with a fantastic product called the drive 90 plus the drive 90 plus is a right angle drill attachment constructed of steel and plastic with a nice molded grip it's one and a half inches wide and weighs only a half a pound which means it's easy to maneuver really lightweight and can fit into any space it features a quarter inch hex shaft which means it can fit any impact driver and drill and it has a quarter inch magnetic hex socket so you won't go losing your bits the drive 90-plus makes drilling into tight confined spaces super simple and easy for more information on the drive 90 or any other other products check out miles craft comp reducing the miles craft drill block no more guessing if your drill is at a true 90 degree angle to your work surface this handy guide system allows you to drill a straight hole every time the drill block has an ergonomic design that is comfortable in any application the unit also features non-slip TPE pads on both sides to prevent slipping and Mauri on the work surface there are center lines on all four sides of the drill block that are lined up with each hole location to help you make sure you are positioned exactly centered on your mark using these as a guide you will drill a perfect hole every time the base of the drill block is made of a reinforced nylon and will not heat up in your hand while drilling through metal the drill block has a solid base that allows it to be clamped for stability the Vblock channel on the underside provides versatility on many different drilling surfaces from round to corner profiles on the top of the bushing block there are six holes for common drill bit sizes 1/8 3/16 quarter inch 5/16 3/8 and 1/2 inch each bushing is held to a tight tolerance and allows you to drill at a 90 degree angle to any surface for drilling holes that are straight and true be sure to check out the miles pass drill block miles craft always the better idea introducing the miles craft tools standard the miles craft tool stand is compatible with most rotary tools including dremel Black & Decker Milwaukee and many more you can easily convert your rotary tool into a jo press or a horizontal tool holder the tool stand you can drill polish sand and even route with your rotary tool included in the box will be everything you need to assemble your tool stand and mount your rotary tool to the tool stand to begin assembling the tool stand turn the base upside down so the scales and the base are facing downward insert each rubber foot into the four screw holes or using four screws included with the tool stand you can mount the unit to any work surface by drilling the screws through the four holes in the base lamps can also be used to secure the unit in place but be sure the clamps are tightly secured and they're not in the way next place the hex nut into the slot of the tube support hole while holding the hex nut in place insert the base ball into the back of the tube support do not fully tighten flip the base over so the scales for facing upward on a flat surface insert the steel tube into the tube support and be sure the steel tube is fully seated into the base securely tighten the bolt to secure the tube in place insert the cord holder into the top of the tube with three prongs going into the to insert the s knob into the hole near the tool holder the main housing can be mounted either horizontally or vertically depending on your application in a vertical position you can drill route sand and more to mount the main housing in the vertical position insert the triangular knob into the hole on the side of the tube holder and then screw the additional hex nut onto the bolt of the knob do not fully tighten slide the main housing over the tube through the vertical slot at the back of the main housing tighten the main housing at any height for the time being to mount the main housing in the horizontal position insert the triangular knob into the hole at the base of the main housing and then screw the additional hex nut onto the bolt or the triangular knot do not fully tighten slide the main housing over the tube through the hole at the base of the main house tighten the main housing in any height to mount your rotary tool to the tool stand you will need either the metric or imperial call it nuts that were provided in the packaging place your rotary tool on the main housing with the tip of the tool going through the hole of the metal holder be sure the on/off speed and lock button switches are all accessible and that the rotary tool is sitting straight in the tool holder thread the collet nut onto the tip of the tool to secure the rotary tool to the metal holder to attach the desired rotary tool accessory to the rotary tool follow the manufacturer's instructions for taching accessories the miles craft tool stan has a strong and sturdy six inch by six inch base with Imperial and metric scales for accurate measurement we're needed the base also has built-in slots that can be used to clamp your work pieces down to the base as needed there's a built in depth stop for your drilling applications the max range of travel when the head is locked into position using the handle is two and a half inches or sixty three point five millimeters the head of the tool stand can be adjusted on the metal rod the max range of travel is seven inches or 17.8 centimeters whether you need to sand polish drill or route with your rotary tool the miles craft tool stan has you covered this tool stand is ideal for any workshop go out and get yours today miles craft always the better idea