Gadgetory

all right so today we're going to take a part three get candy vending machine Wednesdays into ghetto you how to take it apart set the candy settings put a lock on the top kind of all the basics that you need to know to operate one of these guys first step stomp those out alright so in order to adjust the candy setting each one of these you got to remove these two screws down at the bottom and that one right there and the whole head will come up off of the plastic bar on the bottom taking that out as well so I got those three screws out this part itself comes up never really need to mess around with this part those two screws right there just kind of keep these Springs in place you never really need to mess those unless you're going to clean them out so this is what it just lets the candy flow down through it so you can adjust this top part right here put those little grooves up here at the top so the wider that it is the more candy will flow down to small it is the last Daniel's bow down so if you're going to skittles or smaller on candies you want to do something like that we're going to do Eminem's like the peanut ones you want to do something like this or like the mixed nuts would be on the far position like that this whole portion comes out as well you know if you ever want to take it out and clean it so now during this whole plastic piece including all of the these mechanisms you got to take off this bolt that both this one and that one so there's four that you got to remove okay so levels were a nine millimeter on all those sides and it takes a second to pop it out away from the the holsters like the little place where you screw on the nut but this itself is the where the candy falls through so here we have the coin mechanism so that's where the the can you fall through in those little dark places right there and the coin mechanisms themselves they all come apart as well returning time to get the coin mechanism down all you have to do is unscrew this right here on the side and then rotate this so that it's not connecting to that metal part anymore so to spin it see if we can do this with the camera spinning like that and it's not holding into the side anymore and this whole place reaching around to the front will just kind of pull out I can get a better shot off in the front you can see that that has a clip on the side right there so when that clips in this side the other end that we just unscrew it has that little middle part that sticks on the other side to hold the whole thing in so that's how that parts held in the rest of this just kind of slides up and out of the little hole so there what's holding that in is the coin mechanism itself so I'm going to show you how the coin Buddhism itself works so when you're turning this it stops unless there's a quarter down inside so when there's a quarter inside and you turn the quarter allows the mechanism to spin all the way through spits the quarter out the other side stops again time gravity does help you out as well okay so to install a lock there's quite a few pieces here I'll kind of explain which one does this is the main part right here that needs to come up to the bottom doesn't really matter which way this one goes this piece right here it goes on top of that main lock piece to hold it down so once you have that fee down let me take this amount over here and you upper over the top of that to hold the whole thing snug so once that's honest as you can get it take the lock mechanism yourself doesn't really matter which way it goes in I stick a through the bottom now you see on that it's got a little square head so this is the part where you choose how far you have your key to turn yeah these two little gizmos right here this is if you want your key to turn 180 degrees this is if you want your key to turn just 90 degrees there's a little stopping point right there which makes it you know go one way or the other does stopped on those little grooves but I put the 90-degree one on it you can kind of see as I turn it there that it's catching there I turn the key 90 degrees it catches there on that side and so that's what decides what keys turn so once that's in place all right I'm going to take that piece right there and now position it on the top just like that when you take your screw and you're screwing the top of that to hold everything in place right so now at the keys in place I can spin it whichever way I want so this is the open position this is the closed so as you can see in the open position that climbs onto that little piece right there close it over the top lock it that won't open up anymore so anyway that's how you want to change the lock on a three headed vending machine as well as take it apart and adjust all the candy and stuff so I usually put up videos you know a couple times a week you know different projects like this just fixing everything and showing you how to do life so anyway any questions go ahead and leave in the comments and don't forget to subscribe thanks