Gadgetory

so I now have a clear Galaxy s8 and a clear LG g6 I'll show you how I made these in just a second if I want to talk to you about the Galaxy s8 I ran into an issue while I tried to charge it the day after I made my video turns out everything was working just fine the phone calls the service the Wi-Fi everything except for that it wouldn't charge I would get a battery temperature too low a warning sign even though the battery obviously wasn't cold this is not ideal for people who want to use their phone longer than a day turns out there is a small temperature sensing Niblett on the side of the wireless charging pad that has its own little metal contact points with the motherboard I used some scissors to cut through the hard plastic around those contact pads and I also cut through the wireless charging loops leaving just two plastic screw holes the golden contact pads and the niblet itself once I screwed this small segment back into the motherboard I was able to charge and function like normal again so if you do mess this part up you can sometimes get replacement wireless charging coils on eBay for about ten or twenty dollars or just harvest one from a broken galaxy si to test on first or maybe you can just leave your whole wireless charging connected under the glass but either way that nibblet does need to be there for your phone to charge not the ideal design choice I feel like normally that battery temperature sensor is inside the battery itself but on the SI it is outside the battery and inside the wireless charging coil luckily with the LG G 6 we don't have that issue the phone will charge just fine even without the wireless coils inside now let me show you what the LG G 6 looks like when you strip off that outer color just like with every glued shut glass back phone we have to use some heat to soften the adhesive under the glass I don't personally have a hairdryer so I just use my heat gun then I split my thin metal pry tool between the glass and the frame I talked more about this in my LG g6 tear down the long story short just go slow and be gentle as you slice through that glue once the back glass is off I'll pull off the excess adhesive and then I'll get that camera lens out of the frame I thought about making the lens clear since you can see it still has that silver coloring on it but I don't have any spare lenses yet and I don't want to risk cracking this one so I just pulled the whole frame out the fingerprint scanner came out a little easier just make sure not to damage that little ribbon cable along the side now as far as the back panel goes the color is on the underside of the glass just like it was with the s8 they took a second to find the starting point digging through the color until I could get a grip on it and pull it off in one massive chunk slightly easier to remove than the Galaxy sa it feels a lot like aluminum foil and luckily it didn't leave any residue behind on the glass the back of the phone still is Gorilla Glass 5 so it should be pretty shadow resistant now I could just put the glass back on the phone and call it good it still looks pretty high-tech at this point but I think we should take it all the way there are 11 screws holding down that wireless charging and back plastics I'll pop off the wireless charging it doesn't look like this one has any temperature sensing niblets attached to it so we should be just fine without it I'll check in a second the loudspeaker plastics can be popped off as well and just like with the SI we don't need all of it just the speaker section with its golden contact pads I did leave two screw holes intact so it will still be tight against the phone body and now for the moment of truth it still charges without the wireless charging in place so it looks like the temperature sensor for the LG G 6 since it does have one somewhere is either built into the battery or into the motherboard which i think is definitely a better design choice than having it in the wireless charging pad I'll add some of my clear double-sided tape to the camera lens and then press it back into the glass the fingerprint scanner and power buttons are all one unit on the g6 you have to be super careful with this if that ribbon rips the power button will stop working and well you know there's always the chance that your phone will never work again if you attempt this so keep that in mind I'll lay that clear double-sided tape all around the outside of the phone this will help keep dust and lint from your pocket from entering under the glass and getting inside those components so make sure it's fully sealed around that edge I'll clean off the inside of that back glass because once it gets set down into place it's pretty permanent the double-sided tape is pretty strong stuff gently setting the glass panel down into place and pressing it securely all along the edges and there you have it that is one pretty good-looking phone I'll turn it on the phone is still fully functional - the wireless charging Wi-Fi and cell phone signals still function it would be way cool to add one of those old-school rotating mass vibrators inside so we could see a spin but this phone doesn't have one of those unfortunately it's still pretty fun to see all the components though if you notice I did screw all of my screws back into the holes that came from even without that back plastic just be careful not to go too far because they do push through into the back of the LCD and can create pressure points I think both phones look pretty awesome so if you had to pick between the galaxy s 8 and the LG G 6 which one do you think looks cooler on the inside my Instagram followers got a sneak preview of this project before the video actually went live on YouTube so come follow me over there if you're into that kind of stuff and let me know if there's any other phones you want to see clearer versions of down in the comments thanks ton for watching I'll see you around