Gadgetory

hey YouTube welcome back to tech yesterday's run easy coming back to you guys today with a quick video on deleting has well now this is the has little chip here as you can see it's deleted so I just did it I was really nervous so device method is great like it took me two seconds to do this just grab a vise put some little electrical tape there as to grip the heatsink better and just put the heatsink in there and have a little bit of the chip sticking out here and just have something in the background to catch the chip and what I did was I just got this little block of wood here this is little block of wood a little sort of rubber hammer any hammer will do just make sure you're very careful and you just put it on the edge there and you just bang bang bang bang bang bang bang bang bang bang bang bang bang and yeah she comes off like that beautiful and as you can see all there's all this craps like the actual the tea I am they use here is just complete rubbish like I just yell surprise with the like just the crap they use on this is just absolute junk so I mean if they're going to do this paste why don't they just use onyx silver or something I mean cost them you know I'd rather pay an extra dollar for my chip to have cymatics silver on it or something anyway I'm going to apply some new paste here with the line method I'm then going to put my cooler my chip back on and you don't need to glue it back on you just whack it back on the bracket will hold it in place and I'm going to show you before and after temps hey guys let's get onto the before and off the temps alright so on the left here I did a benchmark prime95 and real temp and I got 73 Max and 71 68 65 and that was a six-minute benchmark and then on the right I just did another quick six-minute benchmark and this was exact same ambient temps at 25 degrees ambient temperature and you can see here the there was a 6 degree difference so encore one six degree difference encore two and the other cause were a bit more a little bit less but more even so as you can see there when I did take the screen shot you just see the temps of way more even on the on the deal it at after you deal it and put some arctic silver 5 on so yeah guys I can highly recommend this method and I'll just move on to the conclusion now so let's move on conclusion I will say that the temps dropped by about seven degrees and yeah that's keep in mind that's with a fresh paste of Arctic silver on there so maybe a week later it will be you know even lower so I will say that the temps were more even as well across all the cores which is great so all in all I'm going to recommend this method the vise method I'm not going to recommend the razor blade method because I myself am too nervous to do that like I if I get a razor blade in there now I got rough hands really rough hands if I did the razor blade method I think I would have bricked my chip for sure anyway guys in conclusion I will say like you know I don't have much muscle but I do have a bit of muscle like a little bit so I gotta say if you're scrawny like no bull like no bull you guys probably laughing but I'm yeah if you are scrawny and you're nervous then maybe get someone else to do it maybe your pup's or you you know you friend who goes down the gym or whatnot because you know if you do have the hammer and you know you'll just go bang bang bang and you've got no power and your hammer you know you overstep the wood or the hammer and you you hit you know you just hit the chip somehow you're going to damage the chip because they're pretty easy to damage so keep that in mind so that's all I'm going to say in conclusion guys and if you have any questions or comments please leave a comment in the comment section below or if it's urgent PM me and I do recommend the vise method like seriously so I added like a vise sitting around I had a hammer and just a block of wood already there so I was like when I saw this vise method like this is perfect so yeah it was really it took like an hour the whole process took an hour to do I highly recommend it also another thing is I sorry I did say the line method before I do recommend the spread method instead because of the voltage regulator being right next to the chip so that's another thing but yeah guys all in all I'm going to be going for that 4.8 gigahertz overclock probably when it gets a bit cooler this was with 25 degrees ambient amps as I said before and yeah guys if you like this video please give it a thumbs up and if you haven't read subscribe to take care City and I'll give you giving you guys some more tech alright guys peace out bye