Gadgetory

all preparation before starting to plaster walls you need to properly prepare the surface in order to ensure a better adhesion of the plaster mortar to the walls the preparation procedure is performed by spraying a special mortar on the walls consisting of sand and cement the builders you see on the screen have managed to minimize the amount of time and effort spent on the whole procedure the solution is mixed using a special equipment instead of the traditional manual method it produces large quantities of material at once enough even for large objects the mixing machine can also operate as a powerful pump the craftsman connected a hose to it and then went up the equipment easily pumps the solution over enough though the hose is very long this way their builders easily spray the morsel on the walls like water once the materials applied to the walls it is leveled out for further plastering installing briquette if you've ever seen a clinker brick or any other similar citing material being applied to a wall you know it's a very messy job that requires a lot of patience and precision from the worker even the slightest mistake can result in a crooked row of bricks and then another one and so on as a result he will have to either start again or the result won't look good the innovative briquette system greatly simplifies the job of the builders while increasing productivity on the construction site that is because this way of laying clinker bricks allows you to perform the work approximately three times faster the first stage is not covering the wall with masonry mortar as it's usually done instead metal panels are mounted to the wall this is the only stage where you need to be very precise the panel's must be attached to the walls strictly horizontally when this is done you can proceed with the installation of the bricks attaching them to the metal panels with glue the strip's act as a guide so that the rows of bricks are perfectly even the final step is to fill the joints between the bricks with matter concrete door most people prefer wooden or metal doors but in some places in the world who can find unique handmade concrete doors in order to make one of these a very small number of molds and tools are needed for example to mark the edges of the future door to metal bars are placed on the ground parallel to each other another metal block is used to compact and remove excess material the surface of the future door is finally leveled with the help of spatula the surface of the finished product will have horizontal openings making it look like a grid in order to measure their width that marked the location the worker uses the same metal bar in trailers when the future door is marked it's time to take out the unnecessary concrete slabs for this purpose the surface of these still wet concrete is cut exactly along the markings the cut pieces are lifted up with a knife and then simply removed and pull the site when this stage is over the holes need to be smoothed out using the trowel on the spatula again thus anyone who has a basic set of construction tools some patience and precision can build this door decorative walls finishing modern construction material companies offer a wide range of mixtures solutions paints and varnishes their composition is tailored to ensure that the finish is unusual and unique in this case for example several types of coatings are mixed to create a surface imitating masonry blocks moreover these coatings are not ordinary they have a peculiar texture all the products shown in the video are produced by the serbian company maxima first the wall is coated with acrylic base roller grunt it makes the surface coarser so that the following layers have finish idea better the next layer is maxi deck or travertine Oh as a matter of fact it is lime plaster which is usually applied in order to increase the protective properties at the surface but in this case it also serves for design purposes the material has a thick consistency and is applied to the wall in an even and dense layer before it dries the worker uses a brush to create additional texture then he traces the grooves on the wall to achieve the effect of a surface lined with blocks a layer of acrylic primer is applied after that finally the wall is covered with the translucent decorative paint maxi decor Velachery the surface turns out beautiful and original concrete flooring concrete is probably the most flexible material you can use when you want to create something the video shows how it can be used to make an interesting and unusual flooring at first the mold is filled with thin mortar compacted to evenly fill the mold see the three openings in the middle so far they remain empty but later they will be colored the surface is very large which is why this process requires more complex and bulky tools compared to the creation of a concrete door in this case the floor is supposed to be very dark so a dark grey dye is applied to the concrete this procedure has done several times before stamping the surface is also treated with powder of intermediate color to make these surface look more vivid and rich the stamp itself is needed to make the flooring looked like tiles when the main surface is ready the remaining holes undergo the same procedure the only difference is that the dye is not dark grey but green and orange the final stage of floor creation is coating the surface with acrylic sealant for protection brick' wood houses we want to talk about a French construction company that has revolutionized the way modern wooden buildings are built brick' wood has developed a construction technique where only one component is used to build walls it's a wooden brick the system resembles a Lego construction set first a frame is made of wooden beams then when it is time to erect the wall the blocks are stacked on top of each other they are securely connected to each other through special grooves inside and on the sides the system is passing sit and there are bricks of three sizes thanks to this there are no difficulties on the construction sets notice that during the installation of the wall one block is placed on the outside and the other on the inside the strength of the construction is enhanced by the wooden bars clamped between the two blocks the result is a simple economical and eco-friendly house with proper sound and thermal insulation hey stop being lazy it's time to use that brain of yours welcome to brain time incredible facts from the past the present and even the future the power of nature and wild animals amazing facts and unsolved mysteries you'll find all this and much more hair subscribe now you won't regret it