Gadgetory

the corner clamp by wolf craft opens up new possibilities when screwing or gluing boards together and 90-degree angles for example picture frames simple one-handed operation leaves the other hand free for work the Corner clamp achieves a strong clamping force and provides a flat surface it is suitable for boards with the thickness of 10 to 22 millimeters and automatically adjust to different board thicknesses when building a shelf for example drilling and screw driving can be carried out in one operation the corner clamp is non-slip padded your grips to hold the material firmly in place without marking designed to help woodworkers quickly and accurately set the height of saw blades and router bits or the depth of drill bits and are also great for the setup of fences all sizes from 1/32 of an inch to one inch in 1/32 of an inch increments plus ten metric size blocks with this many sizes the need to stack different blocks is virtually eliminated set you'll find eight set up blocks that fit today's most common plywood widths use them to set your dado cutter width and then use them to check your des toes and rabbet joints for a perfect fit the set up blocks are a great way to set up the distance between your table saw blade and fence or even use it on your bandsaw and now you'll be able to set your fence at 1/16 of an inch for cutting thin strips for that special project and setting the space between your router bits blade and your router fence will take no time at all woodpeckers set up blocks will make your cutting routing and drilling setups more accurate expandable powerful versatile the connect modular clamp system from Crescent redefines expectations of what a clamp can do 500 pounds of holding power secures your work with almost 60 percent more force than comparable clamps that's strong enough to hold heavy objects upright with confidence but the real power of the connect clamp is its integrated connection system that lets you join and rotate multiple clamps to achieve almost any position odd angles and difficult corners like those on cabinets and furniture are securely held in position Crescent twin locks allow you to easily add additional clamps expanding your connection options simply attach a twin lock on the end of the rail and slide another connect clamp into place connect clamps are equally useful as a spreader lift the bar lock slide and reverse the position of the head the trigger action now applies force in the opposite direction large pads provide maximum surface contact and protect delicate surfaces pads can be removed to gain additional clearance when working in tight spaces or around overhanging edges an integrated pipe grip is molded into each connect clamp round objects are locked down tight preventing twisting when cutting and drilling the combination plane was created to replace shelves of wooden planes Veritas has released their own version of that shop or a course that uses both our existing plow plane blades as well as the new ones that are specific to the combination plane the Veritas combination plane has three key components the body the sliding section and the fence assembly the body holds the blade the blade adjustment knob one of the scoring Spurs the depth stop and the handle the sliding section travels on two rods that's secured to the body it also carries a second depth stop in scoring spur this component provides support for wider blades the fence also slides on the two rods and carries to fence knobs the Vence the sub fence adjustment knob and the two sub fence locking knobs the combination plane comes with a set of five inch and 8 inch rods that can be installed for either left or right-handed use to deploy the scoring spur loosen the retention screw and slide the cutter down no deeper than 1/32 of an inch then tighten the screw to lock it into place a convenient feature is the through-hole that allows access to the scoring spur adjustment screws without dismantling the plane the death stops are set by loosening the depth stop lock knob rotating the depth stop adjusting knob then tightening the lock knob again you can set the fence by sliding it on the rods then locking it close to its final position using the fence knobs then loosen the sub fence knobs and gradually bring the fence into final position now let's take a look at how to configure the plane for different tasks the key to success with beading is setting the depth stop such that the bead ends up being slightly below the surface setting up the plane on a scrap piece will allow you to get this setup right fluting blades come with a notch that positions the skate in the center of the blade this is essential for the blade to cut properly reading is essentially a number of beads cut simultaneously the key with these blades is to place the sliding section in line with the second quark this will ensure maximum stability of the plane while working whether you're adding a small detail to a furniture project or sticking mouldings the Veritas combination plane is a great choice