Gadgetory

hi guys welcome to top 5s HD the place for a high tech construction that will make you feel awesome so let's get started number 5 hollow wall before the beginning of the construction make sure the foundation is solid and even at first spot the area you're going to build a wall using string and ruler then dig a deep pit up to 2 feet for a strong foundation if the wall is going to be a hundred centimeters the based should be at least 50 centimeters in width flatten the bottom of the ditch with gravel and stones to level up the surface use a rake and a temper now install wooden blocks and prepare a frame for the concrete and spread it out with a shovel strike the iron rods when the wet concrete turns into solid remove the wooden frame and sweep out now line up the concrete block along with the rocks align all block and mark the spot cut out excessive part if need then apply the mortar and start placing the block on it use the level to make sure that the wall is going up straight follow the staggers pattern and keep placing the blocks fill the empty blocks with the concrete and tamp a little to level up make a line of tartar using a handgun around the inner block edge then place a concrete slab and tamp a little cover the bottom part of the wall using concrete or other available material and finally the wall is ready number four in ground fire pit mark the pit layout using marking paint string and a stake dig the fire pit area add a drain to keep safe from water pour about two inches of paver base around the perimeter of the fire pit circle tamp it and set the concrete block in a circle form pour gravel paper up to four to six inches behind the concrete blocks wet it tamp it and pour again to make another layer also fill the blocks then pour lava rocks in the fire pit so blocks tighten up from both sides to get level lay PVC pipes that should be one inch in diameter horse and over PVC pipe and also cover paver base use a screed to flat finish remove the pipes and fill in with sand before setting the stone now set the pavers around the fire pit and cover the concrete blocks to perks seating part mark the stone and cut it with a saw blade keep installing paver and keep some space between all of them take a level to keep the surface even join the pavers and block using mortar now add edging with landscape spikes once the pavers are done at polymeric sand to hold them tightly sweep the sands in the joint and tap to make level you can also add more sand use a leaf blower and remove the excess whit the paver and let them dry finally fill the perimeter filling the pebbles or soil place the comfortable furniture and enjoy the warmth number three molding assembling precast concrete stairs the installation begins with connecting the shock transyl type q mandrel developed for impact sound insulation the top of the stair is covered with transol type t football which is a connection to staircases once the stair frame is completed the construction workers fill it with concrete shock transyl type L sheet is a damaged proofing system it helps to combine the joints air tightly attach a tape between two joints of the sheet so it becomes dirt protected the fire protection set is consisting of a cover and cuff to achieve fire resistance class our 90 peel off the cover and simply apply insert the support into the wall element until it clicks into place [Laughter] the Assemble stare is ready to go [Laughter] place it carefully on the spot to protect Spiral support put a steel plate below pour concrete at the bottom of the staircase so can next to the slab strongly assemble an optimal connectivity with the safety of the blue line number two bioclimatic pergola first locate a site and mark the placement of four posts mark and fix the base plate at the bottom of the post cut out the upper end in order to clip with another post place the pole on the installed bolt and fix it using a driver after placing all posts on the location join them by connecting the top logs for the wind panel function we require five extra logs connect the corners with wire to ensure the alignment of the angles now stretch a string and Mark spot to fix the window clips after fixing a set of clips carefully insert the panel's every clip has a clip holder so it can be connected to the next clips follow the same process and your pergola will be ready to shine DIY pergola the beauty of your house number one decorative natural stones for outdoor flooring prepare the floor level up the surface of need and sweep out make sure the surface is clean and dry start with masking the edges carefully mask the areas that are not part of the application process so we can avoid any kind of damages apply the primer using a brush or a roller what you find comfortable with for stronger grip to hold the stones then let it dry mix the stones and a concrete mixer or a couple of minutes then ports the area with applied premier before spread the stones around the area using a trowel then sprinkle the decorative luminous rocks tamp down the flush and make sure that the top layer doesn't pop out apply the top coat so it holds everything properly you need some forms to apply the stones vertically cut some copper support application clips to hold the forms fix the copper clips using 2-inch screws then put the wooden form over it also apply some wooden clips to the upper edge so the form becomes unmovable pour the mixture of rocks and stones from the open path after the stones bond strongly remove the covers here it is the gleaming outdoor floor the new construction workers video is on the way please like this video and subscribe our channel so you will get the notification of all upcoming videos